Sometimes the washing machine stops spinning even though we are in need of washed clothes as soon as possible. It is one of the common washing machine damage. If your washing machine won’t spin, it could be that the damage caused requires a repairman, or often a simple repair can get your washing machine working again.
Before repairing your washing machine, you should be able to determine what caused your washing machine to malfunction and which parts you can fix without hiring professional help. Note that some of these repairs may require you to remove the back of the washer to check the internal components
If this is indeed the case, then repairs should only be made after the engine is unplugged and the water source is turned off. Let’s discuss more details below.
1. Drain Pump Clogging
One of the most common reasons why your washing machine stops spinning is when the water can’t drain properly due to a clogged drain pump. This can happen when something gets stuck in the outlet pipe, which in turn prevents the steady flow of water in and out of the machine.
This blockage can occur due to piles of clothing fibers or small objects such as coins and hair clips. You only need to get rid of this dirt if your drain pump is clogged.
2. Unbalanced Sink
When the load is too heavy for the machine, your washing machine will detect a risk. If the drum moves too much or in an unbalanced way, this puts stress on the machine and can cause it to become unbalanced and prevent your washing machine from turning.
An unbalanced laundry load is one of the most common causes of an inadequate spin cycle. Sometimes clothes can stick to one side of the drum, preventing the washing machine from moving. This is most common when washing large, heavy clothes such as blankets or heavy coats.
In addition, some new engines will not reach high speeds with unbalanced loads, which can soak clothes. If you suspect a problem, try resetting the clumped wet laundry and running the spin cycle again.
The easiest way to avoid an unbalanced tub is to make sure you don’t overload your washing machine. You may also need to check that your washing machine is on an even level. Place a support pad on the base of your machine to make sure the sink doesn’t tilt to one side.
3. Gear Motor Wear
The motor cleats on your washing machine are used to connect the drum to the motor. The brushes can wear out over time, which means the machine will fill with water and run normally, but the tub or drum itself won’t rotate and your clothes won’t be cleaned effectively.
There are a number of other reasons why your machine might not work properly. Your machine may be damaged due to a problem with the electrical current, a faulty pump, a faulty motor, or other machine components. However, the problems mentioned above are the most common reasons why your engine might not spin.
Please do not attempt to repair electrical equipment without adequate professional knowledge, training and experience. For professional advice and assistance, please contact a trained technician.
4. Check Power Source
While it may seem like an unnecessary thought, try double-checking that the washer is plugged in. Because it could be that your washing machine is not damaged, but your power outlet is the problem.
Shock that occurs while the washing machine is running can cause the plug to come out of the outlet. If the power cord is properly plugged into the wall outlet, check the electrical meter panel in your home to make sure that your mains fuse hasn’t blown.
5. Incorrect Cable Roll
The electrical conductors plugged into your home by PLN are heavy-duty cables that are different from roll cables. Many roll cords or extension cords are not actually able to conduct enough electricity to start the washing machine motor, what happens next is the washing machine is damaged because the mains voltage is not appropriate.
Using a roll cord or extension cord will shorten the life of the washing machine. If you simply can’t move the washing machine closer to the outlet, plug in a new power outlet a reasonable distance away.
6. Check the Washing Machine Panel
On top-loading washing machines, the small bump on the bottom of the lid pushes the switch when you close it. This serves as a safety precaution when the washing machine door is closed.
The way to test for damage to your washer’s panel is to start the washer with the door open and press the switch manually with a finger. If the engine starts to spin normally, simply bend the protrusion back so that it triggers the rev switch properly.
Another thing that might happen is that the control panel of your washing machine is splashed with water and a short circuit causes it to catch fire. The solution is to replace the PCB by calling a repairman to replace it.